← Back to catalogue
Published

Engineered Material

vr.wm-mat-002 · wm-mat-002-engineered-material

Engineered material grades defined by composition, processing and specified properties.

World Models Physical world and living systems PHY.MAT.ENGR

Bundle → Layer → Finding → Questions Filled

3 bundles · 3 layers · 5 findings · 10 questions

Designation and composition What the material is.

Grade and composition

The designation, standard and chemical composition limits.

Material designation

The material is named by a standard designation or a supplier grade.

  1. Which standard designation or supplier grade identifies the material?
  2. Which standard defines the grade, and in which edition?

Composition

The composition is stated as limits or nominal values per constituent.

  1. What composition limits does the specification set?
  2. Which constituents are registered substances with regulatory obligations?
Properties and processing How the material behaves and how it is made.

Property data

Mechanical, thermal and other properties with test conditions.

Tested properties

Each property value names its test standard, condition and temperature.

  1. Which test standard and conditions produced each property value?
  2. Are the values minimums, typical values or measured values?

Processing state

Heat treatment, temper or curing state that the properties depend on.

  1. Which processing state or temper do the properties refer to?
  2. Does processing change the material's designation?
Compliance and end of life Rules and safe handling over the life cycle.

Safety and compliance

Hazard information, restrictions and recyclability.

Regulatory status

Restricted substances, hazard communication and recycling routes are recorded.

  1. Does the material contain substances restricted or of very high concern?
  2. Which safety data sheet and recycling route apply?

Classifiers Filled

Family
World Models
Category
Physical world and living systems
Entry kind
entity
Navigation path
NAV.PHY.MAT.ENGR
Domain
PHY.MAT.ENGR
Industry
Cross-industry
Tags
engineeredmaterialphy.mat.engr
Also called
M1

What it is Filled

An engineered material is a material produced and specified for use, such as a steel grade, polymer, ceramic, composite or alloy, defined by its composition, processing and resulting properties. The subject is the material kind or grade as specified; a particular batch or lot, a finished product made from it and a pure chemical substance in its regulatory sense are separate subjects.

In scope

  • Grade designations, defining specification references, issuer roles, aliases and revision applicability.
  • Declared composition constraints and material architecture, processing-state descriptors and morphology requirements.
  • Condition-qualified property requirements and evidence-backed claims, with specimen, method, uncertainty and provenance references.
  • Recognition evidence, bounded comparison claims, intended-use restrictions and external safety and environmental assessment references.

Out of scope

  • Chemical-substance master identity, regulatory registration and classification execution.
  • Recipe execution, manufacturing process control, lot production, stock quantities, custody, sampling, test execution and observation master records.
  • Finished-item design, structural allowables derivation, application qualification, substitution approval and certification issuance.
  • Hazardous-material operational instructions, controlled-item manufacture, disposal execution and life-cycle assessment calculation.

Why it exists Filled

Engineered material grades defined by composition, processing and specified properties.

Distinguishing features Filled

  • It is a specified grade or kind, not a physical batch, lot or part.
  • Its properties depend on processing state as much as on composition.
  • Distinct from a chemical substance in regulatory terms, though its constituents may be registered substances.
  • Distinct from a mixture or formulation, which is a recipe of ingredients rather than a structural material grade.

What robots and AI may and may not do Filled

Must not

  • Present typical values as guaranteed minimums.
  • Declare two grades equivalent without a cited equivalence basis.
  • Approve a material substitution in a safety-relevant design.
  • Omit hazard information from a safety data sheet when passing it on.
  • Invent property values that no test or specification supports.

Only with a human decision

  • Qualifying a material for a structural, medical or safety-critical use.
  • Approving a substitution of one material grade for another.
  • Signing a declaration of conformity.

May

  • Look up designations, composition and property data with their test conditions.
  • Compare grades across equivalent standards with stated caveats.
  • Check a material against restricted substance lists.

Moral aspects Filled

  • Wrong material data can lead to structural failure and injury.
  • Workers handling dusts, fibres and nanomaterials face exposure risks.
  • Material choices drive embodied carbon and end-of-life waste.

Who is affected

  • Users of products made from the material
  • Workers in production and processing
  • Designers and engineers
  • Communities near production and disposal sites

Owners Filled

Steward

A standards body or materials producer that defines the grade and maintains its specification.

Roles

Grade definition steward
Govern identity continuity, designation scope and requirement revisions.
Materials reviewer
Review property interpretation, condition dependence, conflicting evidence and proposed comparisons.
Evidence custodian
Maintain master references, rendition integrity, licensing and retention metadata.
Safety and application reviewer
Resolve relevant safety applicability and external qualification referrals within delegated authority.
Local agent operator
Perform authorized local data maintenance and report missing evidence; no physical approval authority.

Master systems

  • Standards catalogue
  • Materials property database
  • Product lifecycle management system
  • Chemical substance registration database

Links to other meta-models Filled

references

  • WM-MAT-001 - Proposed neighbor binding, not a pre-existing ledger edge. Constituent identity only; no substance registration or chemistry master duplication.
  • WM-MAT-003 - Proposed neighbor binding, not a pre-existing ledger edge. Optional formulation binding; a grade may reference a recipe without owning its changes or execution.
  • WM-MAT-004 - Proposed neighbor binding, not a pre-existing ledger edge. Lot claims reference the grade revision; lot stock, custody and production remain external.
  • WM-MAT-005 - Proposed neighbor binding, not a pre-existing ledger edge. Specimen identity and condition reference only; custody and disposal remain external.
  • WM-MAT-007 - Proposed neighbor binding, not a pre-existing ledger edge. Method/run evidence reference only; test planning, execution and validation remain external.
  • WM-MAT-008 - Proposed neighbor binding, not a pre-existing ledger edge. Observation references qualify property assertions; observation master values and lifecycle remain external.
  • WM-MAT-006 - Proposed neighbor binding, not a pre-existing ledger edge. Hazard applicability binding only; no hazard classification execution or legal conclusion.
  • WM-REC-005 - Proposed neighbor binding, not a pre-existing ledger edge. Document edition and clause references; standard identity and document lifecycle remain external.

aligned

  • MatML 3.0 - Historical conceptual exchange alignment; no round-trip or schema conformance claimed.
  • PROV-O 2013 - Conceptual provenance alignment; not an implemented provenance service.
  • MaterialProperty 0.1 - Exploratory pre-alpha vocabulary alignment only; never a required production dependency.

neighbor

  • WM-MAT-001 Chemical Substance and legacy M1 - Legacy M1 combined substances, materials, hazards and lots. Retain only grade-level identity and qualified properties here; reference substance identities. The split ledger leaves the primary legacy card with WM-MAT-001. No legacy conformance assertion is inherited.
  • WM-MAT-003 Mixture / Formulation - A formulation describes a stated combination; a grade defines a controlled material kind and its requirements. The same material can reference both without making these classes disjoint or making a recipe prove a grade.
  • WM-MAT-004 Material Batch / Lot - A lot can claim a revision of this grade. Actual production history, quantities, sites and custody remain in the lot master. A grade does not have a current physical location or inventory.
  • WM-MAT-005 Lab Sample / Specimen, WM-MAT-007 Laboratory Test / Analysis, WM-MAT-008 Observation / Measurement Record - Link specimen, run and observation identities and scoped interpretations; never promote one specimen result to a universal grade guarantee or duplicate test lifecycle.
  • WM-MAT-006 Hazardous-material profile - Reference versioned jurisdiction and physical-form-specific hazard evidence; classification, transport requirements and safety-document lifecycle remain external.
  • WM-REC-005 Standard / Spec Artifact - The standard document and edition are externally mastered. This grade holds its specific designation, clause locator, applicability and requirement interpretation.
  • wm-mat-004-material-batch-lot - A batch or lot is a physical quantity of a material grade.
  • wm-mat-003-mixture-formulation - Formulations are recipes of ingredients rather than material grades.

related

  • wm-mat-006-hazardous-material-profile - Hazard profiles apply to materials containing hazardous constituents.
  • world-m1-material-and-substance - Split off from this legacy card on 2026-10-05; the legacy card keeps the primary subject.

What else AI and robots need to interact with it Filled

Identity and identifiers required Filled

  • A material is identified by its standard designation, such as a steel name or number under a national or international standard, or by a supplier grade name.
  • Constituent substances are identified by CAS Registry Numbers or EC numbers.

Direct properties required Filled

  • Density in kilograms per cubic metre.
  • Tensile and yield strength in megapascals, at a stated temperature and test standard.
  • Elastic modulus in gigapascals.
  • Thermal conductivity in watts per metre kelvin and coefficient of thermal expansion per kelvin.
  • Hardness on a named scale, such as Vickers or Brinell.

Recognition required Filled

  • A material is recognised from markings, certificates, spectrometric composition analysis and property tests.
  • Often confused with a similar grade under a different standard or with an unverified substitute.

Capabilities and actions required Filled

  • Properties can be measured by standard tests.
  • Grades can be mapped across standards with equivalence tables.
  • Composition can be verified by chemical analysis.

Hazards and failure modes required Filled

  • Inhalation of dusts, fibres or nanoparticles during processing.
  • Structural failure from counterfeit or wrongly specified material.
  • Restricted substances in the composition.

Standards and interfaces required Filled

  • Inspection documents under EN 10204 for metallic products.
  • Safety data sheets under the Globally Harmonized System of classification and labelling.
  • ISO 6892-1 tensile testing of metallic materials.

Context of use required Filled

  • Used in design, manufacturing, construction and procurement.
  • Subject to chemical regulation such as REACH where constituents are registered substances.

Sources Filled

  1. MatML Version 3.0 Schema - National Institute of Standards and Technology
  2. Metallic materials - Tensile testing - Part 1: Method of test at room temperature - International Organization for Standardization
  3. Plastics - Determination of tensile properties - Part 1: General principles - International Organization for Standardization
  4. NIST TN 1297: 7. Reporting Uncertainty - National Institute of Standards and Technology
  5. PROV-O: The PROV Ontology - World Wide Web Consortium
  6. Extended safety data sheets - European Chemicals Agency
  7. Environmental management - Life cycle assessment - Principles and framework - International Organization for Standardization
  8. MaterialProperty - Material Schemas - National Institute of Standards and Technology
  9. Regulation (EC) No 1907/2006 concerning REACH (European Union)
  10. Globally Harmonized System of Classification and Labelling of Chemicals (United Nations)
  11. ISO 6892-1 Metallic materials - Tensile testing (ISO)

Open questions

  • Restore independent provider review before any canonical or publishable-draft promotion.
  • Verify full source versions, licensing and claim support, including ECHA guidance and material-specific normative test profiles.
  • Develop and test instance schemas with conflicting designations, confidential constituents, anisotropic properties, condition changes, uncertain evidence, stale safety references and lawful retention cases.
  • Validate optional neighbor bindings and mappings with material-family specialists; expand ceramic, elastomer, foam, semiconductor, biomaterial and additive-manufacturing profiles only when supported.
  • Independent external review is absent; Claude and Grok skipped under the authorized waiver.
  • Direct source HTTP statuses and body hashes are unmeasured; full ECHA text retrieval failed, ISO full texts were not read, and current-version verification is incomplete.
  • No exhaustive ceramic, elastomer, foam, semiconductor, biomaterial or additively manufactured material profile; no property values or design allowables are supplied.
  • Executable nested instance schemas, numerical acceptance rules, uncertainty propagation, equivalence validation and round-trip mappings remain to be developed.
  • No regulatory completeness, safety certification, life-cycle calculation or product qualification is claimed.

Machine files

Provenance

world-models research · reviewable-draft

Built from: models/wm-mat-002-engineered-material/spec.yaml, ver-cy/world-models/card-supplements/wm-mat-002-engineered-material.json